Ftp Return Codes Mainframe
For example, the FTP EXIT return code 16550 indicates the following: 16 The GET command failed. 550 The reply code from the FTP server. Even some "permanent" error conditions can be corrected, so the human user may want to direct his User-process to reinitiate the command sequence by direct action at some point in the This action successfully completes, and the data connection is closed. 227 Entering Passive Mode. (h1,h2,h3,h4,p1,p2) 230 User logged in, proceed. The request cannot be fulfilled by the server The request cannot be fulfilled by the server The request cannot be fulfilled by the server List of FTP server return codes From have a peek at this web-site
Sales: 1.800.290.5054 - 1.210.308.8267 Support: 1.210.366.3993 Contact Us Copyright ©1996-2016 GlobalSCAPE, Inc. Wikipedia® is a registered trademark of the Wikimedia Foundation, Inc., a non-profit organization. Try switching the connection port. 10066 Directory not empty. Back to top viniIntermediateJoined: 12 Jan 2004Posts: 231Topics: 46Location: Maryland Posted: Mon Jan 19, 2004 11:40 am Post subject: Mike, The inconsistency of IP Address as shown in JCL vs. http://www.ibm.com/support/knowledgecenter/SSLTBW_2.1.0/com.ibm.zos.v2r1.halu001/ftpret.htm
Ftp Return Codes Mainframe
is there a default ? FTP uses two ports: 21 for sending commands, and 20 for sending data. Thank you for your feedback! A status code of 150 indicates that the server is about to open a new connection on port 20 to send some data. 200 Series The requested action has been successfully
Text is available under the Creative Commons Attribution-ShareAlike License; additional terms may apply. Explains how to use the server or the meaning of a particular non-standard command. The text is exact and not left to the particular implementation; it must read "MARK yyyy = mmmm" where yyyy is User-process data stream marker, and mmmm server's equivalent marker (note Eza1735i Std Return Code = 16550, Error Code = 00002 Change from PASV to PORT mode, check your firewall settings, or try to connect via HTTP. 426 Connection closed; transfer aborted.
The message was picked up from one JCL and the STEp from other ..but they both give same error message. Ftp Error Code The server will not delete this directory while there are files/folders in it. These codes are used by most FTP servers/clients. http://www.ibm.com/support/knowledgecenter/SSLTBW_2.1.0/com.ibm.zos.v2r1.halu001/ftpret.htm Numbers outside this list are proprietary to the Server or Client that you are using.
The administrator of the remote server must provide you with permission to connect via FTP. 552 Requested file action aborted. Ftp Code 425 Verify command sequence. 504 Command not implemented for that parameter. The connection was forcibly closed by the remote host. 10060 Cannot connect to remote server. 10061 Cannot connect to remote server. Back to top taltymanJCL Forum ModeratorJoined: 02 Dec 2002Posts: 310Topics: 8Location: Texas Posted: Thu Feb 12, 2004 6:04 pm Post subject: MVS systems are ebcdic, everything else is ascii.
Ftp Error Code
Or is it an IP address error? Check This Out This may be a reply to any command if the service knows it must shut down. 425 Can't open data connection. 426 Connection closed; transfer aborted. 430 Invalid username or password A higher level nonstandard code created by Microsoft. 250 Requested file action okay, completed. 257 "PATHNAME" created. 300 Series The command has been accepted, but the requested action is on hold, Thnks. Eza1735i Std Return Code = 10000, Error Code = 00008
Insufficient storage space in system. The command opens a data connection to perform an action, but that action is canceled, and the data connection is closed. If not, contact your hosting provider or ISP." The list below contains standard FTP codes. Source Ensure that you typed the correct user name and password combination.
The user should send another command specifying this information. Sftp Return Codes Next Comments require login or registration. Goodbye.
This may include errors such as command line too long. 501 Syntax error in parameters or arguments. 502 Command not implemented. 503 Bad sequence of commands. 504 Command not implemented for
Make sure the PROMT FOR DESTINATION FILE NAMES box is checked and that TRANFER MODE is set to ASCII MVSFORUMS.comA Community of and for MVS Professionals FAQ Search Quick Manuals Register Try again later. 451 Requested action aborted: local error in processing. Back to top viniIntermediateJoined: 12 Jan 2004Posts: 231Topics: 46Location: Maryland Posted: Fri Feb 13, 2004 4:18 pm Post subject: That indeed worked ..omitting the ASCII i.e. !!! Eza1735i Std Return Code = 27553, Error Code = 00002 Exceeded storage allocation (for current directory or dataset). 553 Requested action not taken.
The users ofcors instructed us to follow whatever was being done in the legacy. I believe that MVS will convert ascii/ebcdic for you if the other side is not MVS. These codes can be found in the OS/390 V2R10.0 eNetwork CS IP User's Guide section of the OS/390 V2R10.0 IBM Communications Server Bookshelf (TCP/IP) book. have a peek here Logged out if appropriate. 231 User logged out; service terminated. 232 Logout command noted, will complete when transfer done. 234 Specifies that the server accepts the authentication mechanism specified by the